Versions Compared

Old Version 2

changes.mady.by.user BAS-IP

Saved on

compared with

New Version 3

changes.mady.by.user BAS-IP

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

You can use this menu to set general control parameters of the access control system, access rules, and identifiers.

Table of Contents

Access management  

At this part, you can change information about: 

  • master card. This card is used to add other cards to panel memory. Here you must specify the card number; 
Aura panel
tab1
styles{"body":{"text":{"color":"#02070e","textAlign":"left","fontWeight":"lighter","fontSize":14}},"header":{"backgroundColor":{"color":"#ffffff"}},"headline":{"alignment":{"horizontal":"start"}},"base":{"border":{"bottom":false,"left":true,"right":false,"top":false,"color":"#ffab0096","width":10,"style":"solid"},"backgroundColor":{"color":"#ffffff"},"borderRadius":{"radius":4},"boxShadow":{"shadows":[{"color":"rgba(0, 0, 0, 0.08)","x":0,"y":1,"blur":1,"spread":0},{"color":"rgba(0, 0, 0, 0.16)","x":0,"y":1,"blur":3,"spread":1}]},"size":{}}}
body

To add a master card if its number is unknown: 

  1. Open Access management tab of panel wen interface. 
  2. Enter 0 in the Master card field and submit changes.
  3. Bring the card to a panel reader and wait for the BEEP signal, which means that the master card has been successfully registered.

To add a user card using the master card: 

  1. Bring the card to a panel reader to switch to the adding user cards mode.
  2. Bring the user card to the reader. After reading the card, you will hear the beep signal, which means the successful registration of the card.
  3. Open the Identifiers tab in the web interface, where the added card will be displayed.
  4. Add missing information about the card and save changes.

The time between adding cards must not exceed 10 seconds. 

This method is convenient for mass and quick identifiers adding. But identifiers are not connected to the necessary apartment, so we recommend adding identifiers through the web interface.

  • master code (no more than 8 characters)is a general code entered on a panel keypad to open a lock. When using two locks control module (SH-42), the master code will open both locks. In this section, you can enable/disable master code use;

Image Added

Wiegand 

In this section, you can select: 

  • wiegand type for a card reader. Wiegand-26, Wiegand-34, and Wiegand-58 types are available for work;
  • identifier representation systems. All identifiers can be displayed in Decimal and HEX numeral systems.

Image RemovedImage Added


Aura panel
tab1
styles{"header":{"backgroundColor":{"color":"#c5e9fb"},"icon":{"size":18,"name":"faInfoCircle","color":"#000"}},"headline":{"text":{"fontSize":14,"fontWeight":"bold","color":"#111111","textAlign":"left","text":"Info"},"alignment":{"horizontal":"start"}},"base":{"size":{"width":400,"height":150},"backgroundColor":{"color":"#cee9ffcc"},"boxShadow":{"shadows":[{"color":"rgba(0, 0, 0, 0.2)","x":0,"y":1,"blur":6,"spread":0},{"color":"rgba(0, 0, 0, 0.4)","x":0,"y":12,"blur":4,"spread":-10}]}},"body":{"text":{"color":"rgba(0, 0, 0, 0.75)","fontSize":14,"fontWeight":"normal","textAlign":"left"}}}
body

Support and update of new Wiegand modes require updating the firmware of the Wiegand controller in the service center. 


Access mode 

There is a multifactor authorization feature in panel settings. In addition to the normal operation of identifiers, you can enable the mandatory use of several identifiers to open the lock/s. For example, the user must first bring the card to the reader and then show a QR code to get access.

In this section, you can enable the necessary access mode. Two options are available:

  • normal mode is basic access by one identifier that is linked to an apartment or user;  
  • global mode activates the use of several identifiers for all added users.  

How to configure Global access mode 

  1. Log in to the device web interface. By default, the username is admin and the password is 123456.
  2. Go to Access management > Access mode.
  3. Choose Global in Mode field.
  4. Select necessary identifier types that users must use to get access: QR code, Card, Access code, Ukey. 
  5. Submit settings. 


Aura panel
tab1
styles{"header":{"backgroundColor":{"color":"#b7eca6c2"},"icon":{"size":18,"name":"faCheck","color":"#000"}},"headline":{"text":{"fontSize":14,"fontWeight":"bold","color":"#000","textAlign":"left","text":"Tip"}},"base":{"size":{"width":400,"height":150},"backgroundColor":{"color":"#cef2c4cf"},"boxShadow":{"shadows":[{"color":"rgba(0, 0, 0, 0.2)","x":0,"y":1,"blur":6,"spread":0},{"color":"rgba(0, 0, 0, 0.4)","x":0,"y":12,"blur":4,"spread":-10}]}},"body":{"text":{"color":"rgba(0, 0, 0, 0.75)","fontSize":14,"fontWeight":"normal","textAlign":"left"}}}
body

It is possible to enable/disable and configure multifactor authorization parameters for concrete users in the corresponding tab.


For correct feature functioning, all identifiers must be linked with users. Also, you can enable normal mode support that allows getting access by one identifier, if it is not linked with the user. So, multifactor authorization will not work for identifiers that are not linked with users. 

Locks management  

At this part, you can configure the functioning of 1 or 2 (when using SH-42) locks. The following parameters can be configured: 

  • lock open time is a period (1-300 sec) during which relay contacts will be closed or open (depending on the lock type), and a lock will stay open;
  • lock open delay is a period (0-300 sec) after which relay contacts will close or open after sending a signal to open a lock;
  • DTMF value for each lock or all locks. It is a code (max length - 4 characters) after entering which the lock will open. By default, all entrance panels are set to receive # to unlock the 1st lock and 0 to unlock the 2nd one.
Aura panel
tab1
styles{"body":{"text":{"color":"#02070e","textAlign":"left","fontWeight":"lighter","fontSize":14}},"header":{"backgroundColor":{"color":"#ffffff"}},"headline":{"alignment":{"horizontal":"start"}},"base":{"border":{"bottom":false,"left":true,"right":false,"top":false,"color":"#ffab0096","width":10,"style":"solid"},"backgroundColor":{"color":"#ffffff"},"borderRadius":{"radius":4},"boxShadow":{"shadows":[{"color":"rgba(0, 0, 0, 0.08)","x":0,"y":1,"blur":1,"spread":0},{"color":"rgba(0, 0, 0, 0.16)","x":0,"y":1,"blur":3,"spread":1}]},"size":{}}}
body

This feature allows you to use non-standard DTMF symbols (#, *, and 0) to open locks.

This solves the problem with usage #, *, and 0 symbols for other functions by third-party devices (for example, SIP phones often use these characters to forward or put a call on hold).

In case of using a private SIP server, be sure to enable the RFC2833 mode for DTMF.

Image Removed

.

  • impulse opening mode: one or multiple pulses. It is available to set pulse duration and time between pulses for multiple pulses mode.
Aura panel
tab1
styles{"body":{"text":{"color":"#02070e","textAlign":"left","fontWeight":"lighter","fontSize":14}},"header":{"backgroundColor":{"color":"#ffffff"}},"headline":{"alignment":{"horizontal":"start"}},"base":{"border":{"bottom":false,"left":true,"right":false,"top":false,"color":"#ffab0096","width":10,"style":"solid"},"backgroundColor":{"color":"#ffffff"},"borderRadius":{"radius":4},"boxShadow":{"shadows":[{"color":"rgba(0, 0, 0, 0.08)","x":0,"y":1,"blur":1,"spread":0},{"color":"rgba(0, 0, 0, 0.16)","x":0,"y":1,"blur":3,"spread":1}]},"size":{}}}
body

If an electromechanical lock is used, it is recommended to select one impulse. If an electromagnetic lock is installed, we recommend setting multiple pulses. These settings will help the locks work correctly and for a long time, especially mechanical as it might break if the voltage is applied to it for too long.

Image Added

Open lock 

In this section, you can remotely open lock #1 or lock #2 (when using SH-42) by clicking the corresponding button.  

Additional settings 

Here you can: 

  • set the Floor number for further features that work only with the lift control module EVRC-IP;
  • enable/disable features of sending the elevator to the indicated floor number when the lock is open using identifier or from the monitor;
  • enable/disable monitor secure mode is a feature of alarm deactivation on an indoor monitor when bringing an identifier (that is linked with the monitor) to the panel reader.

External Wiegand controller 

BAS-IP panel can be connected with an external controller via the Wiegand interface. In the section, you can enable/disable playing custom sound and displaying a custom text when the lock is open. 

You also can customize sound and text notifications for door opening by identifiers added to the controller. 

Server manage access 

In this section, you can enable and configure working mode when all identifiers are not stored in a panel memory but on a server. When the identifier is brought to the reader, the panel will send a request to the server and wait for a response - to give access or not.

To configure this feature you must: 

  1. Log in to the entrance panel web interface. By default, the username is admin, and the password is 123456.
  2. Open the Access management tab and find the Server manage access section.
  3. Enable the feature.
  4. Click Use custom server and enter it. You can use Link server.
  5. Submit settings.


Aura panel
tab1
styles{"header":{"backgroundColor":{"color":"#c5e9fb"},"icon":{"size":18,"name":"faInfoCircle","color":"#000"}},"headline":{"text":{"fontSize":14,"fontWeight":"bold","color":"#000","textAlign":"left","text":"Info"}},"base":{"size":{"width":400,"height":150},"backgroundColor":{"color":"#cee9ffcc"},"boxShadow":{"shadows":[{"color":"rgba(0, 0, 0, 0.2)","x":0,"y":1,"blur":6,"spread":0},{"color":"rgba(0, 0, 0, 0.4)","x":0,"y":12,"blur":4,"spread":-10}]}},"body":{"text":{"color":"rgba(0, 0, 0, 0.75)","fontSize":14,"fontWeight":"normal","textAlign":"left"}}}
body

The timeout for receiving a response from the server is up to 15 seconds. After this time, the panel automatically goes to its database and gives access or not.


Face recognition 

Visitors faces can be used as an identifier to get access to a place. Here you can enable and configure this feature. 

1. Log in to the entrance panel web interface. By default, the username is admin and the password is 123456.

2. Open the Access management tab and find the Face recognition section.

3. Enable the feature by ticking the corresponding box.

4. Choose similarity level (the lower the similarity level, the greater the error can be in scanning a face and granting access): 

    • low: the minimal similarity is necessary for access (changes in appearance (glasses, beard, presence of a hat) will not be taken into account);
    • normal: some changes in appearance are taken into account, but not detailed (recommended for homes and offices);
    • high: the maximum similarity is necessary for access (recommended for high-security places).

5. Choose the appropriate mode: 

    • software: the software recognition algorithm is used, there is a possibility of giving access by photos;
    • anti-spoofing: more detailed software recognition algorithm is used to prevent access by photos;
    • 3D (is available for panels with a built-in 3D sensor): detailed face recognition using IR sensors and building a face heat map to prevent spoofing.

6. Submit settings.

Also, you can turn on/off automatic face recognition when motion is detected. When a person approaches a panel (at a distance up to 50 cm) motion sensor becomes active, and a panel will exit standby mode and turn on the face recognition feature.

QR recognition 

QR codes also can be used as identifiers. Here you can enable/disable QR code recognition in general and when motion is detected (at a distance up to 50 cm motion sensor becomes active, and a panel will turn on the QR recognition).

Exit button 

You can connect a button to a panel for lock opening from the inside. At the section, it is possible to activate/deactivate an exit button.

Door sensor input 

It is possible to connect a door sensor or additional button to the door sensor input. In this section, you can enable/disable and configure their work.

After device installation and electric connection, you must do the following steps for correct work: 

1.  Log in to the entrance panel web interface. By default, the username is admin and the password is 123456.

2. Open the Access management tab and find the Door sensor input section.

3. Enable sensor or button functioning by ticking the corresponding box.

4.  Choose the appropriate input mode:

    • door sensor mode is used to monitor the door state. If the door is not closed, after the expiration of the response time in Logs/Syslog/Link logs/Email notifications will be shown that the door is open;
    • door entry button mode is recommended when the connected button is used as an additional, remote from the panel, entry button;
    • concierge call mode is appropriate when the connected button is used to call the concierge using the internal protocol.

5. Set the Response time after which the mode will be activated.

6. For Door sensor and Door entry button modes, you can enable the option to resend a trigger message to Logs/Syslog/Link logs/Email notifications and set the delay time before resending.   

7. Submit settings.

Also, you can check and update the current door sensor input status (open/closed).