Access management

You can use this menu to set general control parameters of the access control system, access rules, and identifiers.

Access management  

At this part, you can change information about: 

• master card. This card is used to add other cards to panel memory. Here you must specify the card number; 

Access mode 

There is a multifactor authorization feature in panel settings. In addition to the normal operation of identifiers, you can enable the mandatory use of several identifiers to open the lock/s. For example, the user must first bring the card to the reader and then show a QR code to get access.

For correct feature functioning, all identifiers must be linked with users. Also, you can enable normal mode support that allows getting access by one identifier, if it is not linked with the user. So, multifactor authorization will not work for identifiers that are not linked with users. 

Locks management  

At this part, you can configure the functioning of 1 or 2 (when using SH-42) locks. The following parameters can be configured: 

• lock open time is a period (1-300 sec) during which relay contacts will be closed or open (depending on the lock type), and a lock will stay open;
• lock open delay is a period (1-300 sec) after which relay contacts will close or open after sending a signal to open a lock;
• DTMF value is a code (max length - 4 characters) after entering which the lock will open. By default, all entrance panels are set to receive # to unlock the 1st lock and 0 to unlock the 2nd one;

Open lock 

In this section, you can remotely open lock #1 or lock #2 (when using SH-42) by clicking the corresponding button.  

Additional settings 

Here you can: 

• set the Floor number for further features that work only with the lift control module EVRC-IP;
• enable/disable features of sending the elevator to the indicated floor number when the lock is open using identifier or from the monitor;
• enable/disable monitor secure mode is a feature of alarm deactivation on an indoor monitor when bringing an identifier (that is linked with the monitor) to the panel reader;

External Wiegand controller 

BAS-IP panel can be connected with an external controller via the Wiegand interface. In the section, you can enable/disable playing custom sound and displaying a custom text when the lock is open. 

You also can customize sound notifications for door opening by identifiers added to the controller. 

Server manage access 

Face recognition 

Visitors faces can be used as an identifier to get access to a place. Here you can enable and configure this feature. 

1. Log in to the entrance panel web interface. By default, the username is admin and the password is 123456.

2. Open the Access management tab and find the Face recognition section.

3. Enable the feature by ticking the corresponding box.

4. Choose similarity level (the lower the similarity level, the greater the error can be in scanning a face and granting access): 

• • low: the minimal similarity is necessary for access (changes in appearance (glasses, beard, presence of a hat) will not be taken into account);
  • normal: some changes in appearance are taken into account, but not detailed (recommended for homes and offices);
  • high: the maximum similarity is necessary for access (recommended for high-security places).

5. Choose the appropriate mode: 

• • software: the software recognition algorithm is used, there is a possibility of giving access by photos;
  • anti-spoofing: more detailed software recognition algorithm is used to prevent access by photos;
  • 3D (is available for panels with a built-in 3D sensor): detailed face recognition using IR sensors and building a face heat map to prevent spoofing.

6. Submit settings.

Also, you can turn on/off automatic face recognition when motion is detected. When a person approaches a panel (at a distance up to 50 cm) motion sensor becomes active, and a panel will exit standby mode and turn on the face recognition feature.

QR recognition 

QR codes also can be used as identifiers. Here you can enable/disable QR code recognition in general and when motion is detected (at a distance up to 50 cm motion sensor becomes active, and a panel will turn on the QR recognition).

Exit button 

You can connect a button to a panel for lock opening from the inside. At the section, it is possible to activate/deactivate an exit button.

Door sensor input 

It is possible to connect a door sensor or additional button to the door sensor input. In this section, you can enable/disable and configure their work.

After device installation and electric connection, you must do the following steps for correct work: 

1.  Log in to the entrance panel web interface. By default, the username is admin and the password is 123456.

2. Open the Access management tab and find the Door sensor input section.

3. Enable sensor or button functioning by ticking the corresponding box.

4.  Choose the appropriate input mode:

• • door sensor mode is used to monitor the door state. If the door is not closed, after the expiration of the response time in Logs/Syslog/Link logs/Email notifications will be shown that the door is open;
  • door entry button mode is recommended when the connected button is used as an additional, remote from the panel, entry button;
  • concierge call mode is appropriate when the connected button is used to call the concierge using the internal protocol.

5. Set the Response time after which the mode will be activated.

6. For Door sensor and Door entry button modes, you can enable the option to resend a trigger message to Logs/Syslog/Link logs/Email notifications and set the delay time before resending.   

7. Submit settings.

Also, you can check and update the current door sensor input status (open/closed).