Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Current »

To make a call between a panel and an indoor video entry phone (monitor) by pressing the button of the required apartment or entering its number, the panel and the monitor must have the same building and unit number in apartment settings. Also for monitors, you must indicate corresponding information about the floor, apartment, and device number.

If there is no monitor, it is turned off or such settings are missing, you must make forward queues for apartments to redirect calls to IP addresses or SIP numbers.

For digital two-wire systems, it is obligatory to configure a forwarding queue for each apartment.

During a call, the entrance panel checks its forwarding queue only when it fails to find any monitors according to the entered values of the building, unit, floor, and apartment. If you want to enable the Forwarding from the beginning (without searching the corresponding monitor via the internal protocol), you need to set different logical addresses for the panel and the monitor. For a detailed explanation of the correct logical address configuration, please refer to the Forwarding from the entrance panel article.

Forward settings  

Two forwarding modes are available: 

  • all at once: the call is made to all numbers simultaneously. 

  • one by one: the call is made to the numbers in turn with a 20-second delay.

If you have an analog and IP device in the same queue, the All at once mode do not work. 

How to make a new forward queue

  1. Log in to the entrance panel web interface. By default, the username is admin, the password is 123456.

  2. Open the Forward tab and click New Forward.

  3. Enter your Apartment Number which consists of the floor and room number. For example, 223 indicates apartment 23 located on the 2nd floor. Entering this number on the panel the queue will work.

  4. Enter the Forward Number (directions for call forwarding). You can add up to 8 numbers for forwarding. Calls can be made both via P2P and via the SIP protocol.

Format for calls via P2P: 

Two formats for numbers are available:

  • sip:1@192.168.1.65, where 1 is the desired number to be displayed for the callee, 192.168.1.65 is the IP address of the callee SIP client (if you use a softphone, the IP address of a device where the softphone is installed);

  • sip:192.168.1.65, where 192.168.1.65 is the IP address of the callee SIP client (if you use a softphone, the IP address of a device where the softphone is installed).

Format for calls to SP-02 is: 

  • sip:192.168.1.99, where 192.168.1.99 is the IP address of the callee handset. 

Format for calls via SIP:

You can also use the short form and enter only the callee SIP number of the called device ("sip:" at the beginning and the SIP server address can be skipped). So, it is enough to enter 5588.

For the forwarding correct function, the SIP numbers in one queue must be registered on the same SIP server. For example, forwarding will work for your SIP numbers registered on the us.sip.bas-ip.com server.

Format for calling the handset of a digital two-wire system:

  • laskomex:2, where 2 is an apartment number

 Format for calling the handset of a coordinate matrix system:

  • vizit:2, where 2 is an apartment number

  1. Save the forward queue by clicking Confirm.

Forwarding will work correctly even if numbers for both P2P and SIP calls are entered in the same queue.

Example of panel operation in combination with a coordinate matrix system

We are required to call apartment 27. When entering the 27 value on the panel, it makes a call via internal protocol to the monitor in apartment 27. Next, the panel accesses the Visit switching units and calls the Visit handset with 27 number. Then the panel refers to the forwarding table to check if there are any records for apartment 27.

Then there are several ways for the panel to act:  

  • if there is no record for apartment 27 or it is empty, the panel will end the call.

  • if there is a vizit:45 number, the panel will call the Laskomex handset with the No. 45.

  • if for the 27th apartment, the SIP or P2P number is entered, e.g., sip:1346@us.sip.bas-ip.com, the panel will make a call to the specified number via SIP or P2P.

  • if there are several numbers indicated, e.g., vizit:45;sip:1346@us.sip.bas-ip.com, the panel will make a call in order the numbers are specified, i.e., first to the Vizit handset with the 45th number, and then to the specified SIP number. 

Example of panel operation in combination with a digital two-wire system

We are required to call apartment 27. When entering the 27 value on the panel, it makes a call via internal protocol to the monitor in apartment 27. Then, the panel refers to the forwarding table to check if there are any records for apartment 27.

Then there are several ways for the panel to act:  

  • if there is no record for apartment 27 or it is empty, the panel will end the call.

  • if there is a laskomex:27 number, the panel will call the Laskomex handset with the No. 27.

  • if for the 27th apartment, the SIP or P2P number is entered, e.g., sip:1346@us.sip.bas-ip.com, the panel will make a call to the specified number via SIP or P2P.

  • if there are several numbers indicated, e.g., laskomex:25;sip:1346@us.sip.bas-ip.com, the panel will make a call in order the numbers are specified, i.e., first to the Laskomex handset with the 27th number, and then to the specified SIP number. 

  • No labels